Custom Steel Pool Stair Fabrication & Installation — Highland, Utah
Quick Project Summary
Titan Forge LLC designed, fabricated, and installed a custom steel pool stair with precast concrete treads for a home in Highland, Utah.
The homeowners had a raised diving board platform beside their pool with no permanent way to get onto it. They were using a step ladder. We built a five-riser steel stair that bolts to the platform structure at the top and to the concrete patio at the bottom.
The finished stair is 48 inches wide, with 38 inches of total rise and 48 inches of run. Five risers at 7-5/8 inches each carry four precast concrete treads at 12 inches deep. The stringers are C8 structural steel channel, finished in matte black powder coat.
What shaped this project was where it had to be installed. A pool deck with finished stone, a swimming pool a few feet away, and a patio with drainage fall built into it. So the entire stair was engineered to be assembled on site with zero field welding.
PROJECT OVERVIEW
Fabricator & Installer: Titan Forge LLC
Location: Highland, Utah
Project Type: Custom residential steel pool stair with precast concrete treads
Existing Condition: No permanent access to a raised diving board platform; homeowners were using a step ladder
Overall Width: 48 inches
Total Rise: 38 inches
Total Run: 48 inches
Risers: Five at 7-5/8 inches
Treads: Four precast concrete treads at 12 inches deep
Stringers: C8 structural steel channel
Tread Support: Welded 90-degree steel brackets with slotted holes, plus a C-channel base plate under each tread
Tread Attachment: 3/8-inch bolts into threaded inserts cast into the underside of each tread
End Connections: 1/4-inch steel plate brackets, bent to 90 degrees, welded to each stringer end and bolted to the platform structure above and the concrete patio below
Field Welding: None — the stair was designed to bolt together on site
Finish: Matte black powder coat
Precast Treads: Capital Precast, Orem, Utah
Install Time: Approximately 1.5 hours
Warranty: One-year Titan Forge workmanship warranty
FROM A STEP LADDER TO A REAL SET OF STAIRS
The pool and the raised platform were already built. The platform carries a diving board and sits about waist height above the pool deck, and there was no permanent way up to it.
So the family was using a step ladder.
A step ladder next to a swimming pool, with wet feet, is not a long-term answer. It is also the kind of thing you stop using, which means an expensive feature of the backyard quietly goes unused.
What the homeowners wanted was straightforward: a real set of stairs, built to last outdoors, that looked like it belonged with the rest of the pool deck.
DESIGNED TO BOLT TOGETHER INSTEAD OF WELD TOGETHER
Every weld on this stair happened in our Springville shop. Nothing was welded at the property.
That was a deliberate decision, and it was driven by the site.
Welding on a finished pool deck means sparks and hot spatter landing on stone pavers, grinding dust settling into the water, and burn marks on surfaces the homeowners just paid for. It also means running power and hot work within a few feet of a swimming pool.
The cleanest way to avoid all of that is to not do it. So we designed the stair as a kit of prefabricated parts that go together with bolts.
The stringers were cut, drilled, and welded complete in the shop. The tread brackets were welded on in the shop. The end connection plates were welded on in the shop. Then the whole assembly went out for matte black powder coat before it ever went to the property.
That last part matters more than it sounds. If you weld in the field, you are grinding and touching up paint in the field, and a touched-up spot never matches a factory finish. Coating the finished assembly means every surface on the stair has the same coating, applied the same way, with no bare steel anywhere for water to find.
SLOTTED HOLES SO THE STAIR COULD BE DIALED IN ON SITE
When you give up field welding, you give up the ability to fix things by cutting and re-welding. So the adjustment has to be built into the parts before they leave the shop.
Each concrete tread sits on a pair of 90-degree steel brackets welded to the stringers. Every hole in those brackets is a slot rather than a round hole.
A slot lets the bolt move. That gives the installer roughly a quarter inch of movement in either direction to bring each tread level before the bolts get tightened down.
That sounds like a small allowance until you look at where the stair lands. A concrete patio around a pool is not built dead flat. It is poured with a slight fall so water runs away from the house instead of pooling on the deck. The bottom of the stair sits on that slope, and the top bolts to a platform that was framed by somebody else, months earlier.
Slots absorb that. Without them, you are back to hoping two independently built structures happen to line up, and hope is not a fabrication method.
THERE IS STEEL UNDERNEATH EVERY CONCRETE TREAD
The treads on this stair are precast concrete, supplied by Capital Precast in Orem, Utah, with steel reinforcement cast inside.
Two details make them work.
First, the attachment. Rather than drilling into finished concrete on site, the precast supplier cast threaded inserts directly into the underside of each tread during the pour. 3/8-inch bolts pass up through our brackets and thread straight into them. The bolt pattern we gave them and the inserts they cast lined up on the first try, with no drilling, no shimming, and no adjusting on site.
Second, and more important structurally, there is a base plate cut from the same C-channel as the stringers running underneath each tread.
That makes every step a composite: reinforced concrete on top, structural steel channel underneath, bolted together into one piece. The concrete handles the wear and the walking surface. The steel underneath handles the bending.
This matters because these treads span the full 48-inch width of the stair. A concrete slab that wide, carrying its own weight plus somebody stepping onto the middle of it, is being asked to bend. Concrete does not like being bent. Over enough seasons of that, plus freeze and thaw, it develops cracks.
With the channel underneath, the concrete is not carrying itself. The steel is. The tread is just riding on top of it.
ANCHORED AT THE TOP AND AT THE BOTTOM
Both ends of both stringers got a bracket cut from 1/4-inch steel plate, bent to 90 degrees, welded on in the shop, with slotted holes.
The top brackets bolt into the framing of the diving board platform. The bottom brackets bolt down into the concrete patio.
Nothing about this stair is free-standing. It is not relying on its own weight to stay where it was set, and it cannot slide, walk, or tip away from the platform.
That is a bigger deal beside a pool than it is anywhere else. If a set of stairs shifts a half inch away from the structure it serves, you have just created a gap at the top of a stair, at the edge of a swimming pool, that somebody will step into.
AN HOUR AND A HALF ON SITE
Total installation time was about an hour and a half, and most of that was lining up the bolt holes at the platform.
That number is the whole point of the approach.
All of the difficulty on this project was moved into the shop, where we have the tools, the fixtures, and the ability to check our work before anything leaves the building. What arrived at the property was a set of finished parts and a bag of hardware.
A backyard is somebody’s home. The less time we spend in it, the less of an imposition the project is on the family living there. Ninety minutes with no grinding, no sparks, no cleanup and no touch-up paint is a much better afternoon for a homeowner than a two-day install with a welder running next to their pool.
THE PART THAT MADE IT WORTH IT
The homeowners came out while we were still packing up.
They went up and down the stairs. They stood on them and jumped on them. They grabbed the stringers and tried to wiggle them.
Then they told us they were thrilled.
I like that they tested it. Somebody who bounces on a new set of stairs before the crew leaves is somebody who was genuinely worried about whether it would feel solid, and now knows it does.
Going from a step ladder to a permanent set of stairs changes how a family actually uses their backyard. That diving board goes from being slightly awkward to get to, to being something the kids run up without thinking about it.
That is the part I care about. The channel sizes and the bolt patterns are just how you get there.
WHAT THIS PROJECT DEMONSTRATES
For homeowners, pool builders, landscape contractors, and general contractors looking for a custom steel stair fabricator in Highland, Alpine, Lehi, American Fork, or anywhere in northern Utah County, this project demonstrates our ability to handle:
- Custom steel stair design and fabrication for existing structures
- Stairs built to assemble on site with no field welding
- Work on finished pool decks, patios, and other sensitive surfaces
- Steel-and-precast-concrete composite tread assemblies
- Coordination with precast concrete suppliers on cast-in threaded inserts and bolt patterns
- Slotted-hole connection design for field adjustment
- C-channel stringer fabrication
- 1/4-inch plate end connections anchored to structure above and slab below
- Powder coating of complete assemblies before delivery
- Short, low-impact installations at occupied residences
The thing worth taking away from this one is the design decision behind it:
The right time to solve an installation problem is before the truck leaves the shop.
Frequently Asked Questions
Can you build steel stairs without welding on my property?
Yes, and on finished surfaces we prefer it. This Highland pool stair was fabricated and welded complete at our Springville shop, powder coated as a finished assembly, and then bolted together on site. No welding, grinding, sparks, or touch-up paint at the property.
How do steel stairs with concrete treads go together?
The stringers are the two angled steel members that carry the stair. We weld 90-degree brackets to them to support each tread, then bolt the treads down through those brackets. On this project the precast supplier cast threaded inserts into the bottom of each tread, so 3/8-inch bolts thread straight into the concrete with no drilling on site.
Will a concrete tread crack over time?
It can, if nothing is supporting it. A tread spanning 48 inches with only its ends held is being asked to bend, and concrete does not handle bending well. On this stair we ran a C-channel base plate underneath every tread, so the steel carries the load and the concrete just provides the walking surface.
What size steel did you use for the stringers?
C8 structural steel channel, finished in matte black powder coat.
How do you get a prefabricated stair to fit when the patio is not level?
We build the adjustment into the parts. Every hole in the tread brackets and end connection plates on this stair is a slot rather than a round hole, which gives the installer roughly a quarter inch of movement in either direction to bring everything level before the bolts are tightened. Pool decks are poured with a slight fall for drainage, so that allowance matters.
How are the stairs anchored?
Both ends of both stringers have a 1/4-inch steel plate bracket bent to 90 degrees and welded on. The top brackets bolt into the structure the stair serves, and the bottom brackets bolt into the concrete slab. The stair is mechanically fastened at both ends rather than free-standing.
How long does an installation like this take?
This one took about an hour and a half, most of it spent aligning the bolt holes at the top. Prefabricating everything in the shop is what keeps site time short.
Do you build custom stairs for pools and outdoor spaces in Utah County?
Yes. Titan Forge fabricates custom steel stairs, railings, and structural steel for residential and commercial projects throughout Utah County and surrounding areas, from our shop in Springville, Utah.
Does Titan Forge warranty this kind of work?
Titan Forge provides a one-year workmanship warranty on its fabrication and installation work, subject to the terms applicable to the project.
Custom Steel Stair Fabrication in Highland & Northern Utah County
Titan Forge LLC is a welding and metal fabrication company based in Springville, Utah, building custom steel for homeowners, contractors, builders, and businesses throughout Utah County.
We do a lot of work in Highland, Alpine, and the surrounding communities, where backyards tend to include pools, elevated patios, retaining walls, and outdoor structures that were never designed around an off-the-shelf stair or railing.
This project is a good example of what that usually requires: an existing structure someone else built, finished surfaces that cannot be damaged, and a stair that has to be fabricated to fit a set of conditions that only exist at that one property.
If you have a pool deck, patio, or elevated platform that needs stairs or railing, we can review photos, measurements, or drawings and tell you how we would build it.
Custom fabrication is mostly about deciding what happens in the shop and what happens on site. We put as much of it as possible in the shop.
Send us photos, measurements, drawings, or your project scope. We’ll review the job, identify the fabrication and installation considerations, and outline the next steps.


